
Controller
SKYLED WiFi Controller
The brain of the system. An open-firmware WiFi controller (WLED) with a built-in microphone. It joins your home WiFi once, then runs from the app. Two models: Pixel + PWM, or Pixel.
each
- 2.4 GHz WiFi: no hub, no bridge, no mandatory cloud.
- Open WLED firmware, updated over WiFi.
- Built-in microphone: light follows the music.
- Pixel + PWM model: also drives regular RGBCCT, RGBW, RGB, CCT and single-color strips.
- After a power outage, the light comes back exactly as it was.
The SKYLED app
One app.
For all your lighting.
No more one remote for the living room and another for the kitchen. Every SKYLED controller in the house, every room, every strip, pixel or not: one app runs them all. The same on your phone, tablet, computer and wall tablet.



Universal
One screen for every controller and every zone in the house. Not one app per light.
On every screen
Android or iPhone, iPad, tablet, Windows or Mac computer. Same app, same settings.
Instant at home
Commands go straight over your home WiFi: no hub, no mandatory cloud.
Remote control
Turn lights on or off or change scenes from anywhere. Coming soon.
Wall tablet
A full-screen mode for a wall-mounted station: clock, scenes and automatic return.
Always up to date
New scenes, moods and features added by update, with a "What's new" screen.
Guided setup
The app finds your controllers, blinks them so you can tell them apart and sorts them by room.
Diagnostics
The app warns you when a controller has weak WiFi or is offline.
Technical data
Full specifications.
| Both models | |
|---|---|
| Network | 2.4 GHz WiFi |
| Processor | ESP32 |
| Firmware | WLED (open source), updated over WiFi |
| Microphone | built-in (music mode) |
| Control | SKYLED app: phone, tablet, computer |
| Supported pixel ICs | WS2805, WS2811, WS2812B, WS2814, WS2815, SK6812 |
| WiFi setup | once: "WLED-AP" access point or USB-C cable, then your home WiFi |
| Pixel + PWM model | |
| Input voltage | 5 to 24V DC |
| Pixel outputs | 2 outputs, up to 2048 pixels |
| PWM outputs | 5 channels, 6 A max. per channel |
| Total current | 12 A max. |
| Barrel jack | 4 A max. (above that: terminals) |
| Supported PWM strips | single color, CCT, RGB, RGBW, RGBCCT |
| Operating temperature | -10 to 40 °C |
| USB-C port | wired firmware update (UART) |
| Addressable pixels | up to 2048 pixels |
| Power input | screw terminals, or 5.5 × 2.1 mm barrel jack (4 A max.) |
| Data pinout | DATA1 = IO16, DATA2 = IO2 |
| PWM pinout | R = IO25, G = IO26, B = IO27, W = IO12, C = IO14 (NMOS) |
| Microphone | analog, IO36 |
| Button | IO0: short press = on/off; 1 s = color; 10 s = reset (WLED-AP access point) |
| Spare input | IO33 + GND, for a push button or wall switch |
| Radio remote | RF-to-IR receiver on IO32 (optional 2.4 GHz remote) |
| Indicator | green, steady when powered |
| Use | indoor |
| Pixel model | |
| Input voltage | 5, 12 or 24V DC, constant voltage |
| Data outputs | 2 (GPIO16 and GPIO2) |
| Current per output | 10 A max. |
| Total current | 15 A max. (fused) |
| Strip power relay | built-in (cuts the strip when off) |
| Microphone | built-in |
| Buttons | Restart and Function |
| Spare input | IO33 + GND |
| Expansion header | 5V, 3.3V, GND, IO25, IO18, IO19 |
| USB-C port | wired firmware update (UART) |
| Wiring | lever terminals: V+, V-, GPIO16, GPIO2, GND |
| Rating | IP20 |
| Operating temperature | -20 to 45 °C |
| Housing length | approx. 128 mm |
Good to know
- Full dimensions: after bench testing (end of November).
